1. Home
  2. KST System technology
  3. Gas systems
  4. Gas utilization
  5. Burner systems
  6. 07 Single burner system, modulating-controlled

KST – KROMSCHRÖDER SYSTEM TECHNOLOGY

DOCUTHEK

You can find all documents here.

 

docuthek.com

Burner control

overview

Single burner system, modulating-controlled

Single burner system, modulating control, no air preheating, Pilot burner, pneumatic ratio control system, Ionization control
Flowchart No.: 1.1.1.2.1.1a
Standard: EN 746-2

Process control systems

No Component description Standards and Docuthek
010 Automatic shut-off valve, e.g. solenoid valves for gas VAS

 

020 Air/gas ratio control, e.g. air/gas ratio control GIK

Pressure regulators should be designed to be as small as possible.
Our tip: to achieve good control characteristics, the maximum pressure gradient (difference between the inlet pressure and the required outlet pressure of the regulator) should be fully utilized.

030 Valve combination VCG, as an alternative to the individual devices automatic shut-off valve (VAS) and air/gas ratio control (VAG)
040 Manual adjusting element for gas, e.g. flow adjusting cocks GEHV and GEH
050 Stainless steel bellows unit, e.g. Type EKO

 

060 Industrial burner for gas with pilot burner, e.g. BIO..L, ZIO..L, BIC..L, ZIC..L

he burner’s flexibility is increased thanks to a pilot burner. The control range can be extended incrementally with an optional integrated pilot burner.
These burners can be combined with a burner quarl or ceramic tube. Selection is dependent on the process and system requirements such as capacity, temperature, flame shape and outlet velocity as well as furnace wall thickness and gas type.

070 Control valve with actuator, e.g. BVA with IC

Select the smallest control valves possible so that the opening characteristic can be fully utilized. Note the residual flow when the valve is closed.

080  

Manual adjusting element for air, e.g. butterfly valve for air BVA with manual adjustment

Pursuant to EN 746-2, all manual air control valves must be blocked in the required positions and secured against unintentional maladjustment.

090 Burner control unit BCU 480 for pilot and main burner combination, as an alternative to the individual devices automatic burner control unit and ignition transformer

The burner control unit is mounted to the burner on site and ensures simple commissioning of the burner system.

100 Gas pressure regulator, e.g. 60DJZ
110 Automatic shut-off valve, e.g. solenoid valves for gas VAS

 

120 Valve combination VCS, as an alternative to individual automatic shut-off valve devices
130 Stainless steel flexible tube, e.g. ES

 

140 Air pressure regulator, e.g. 60DJLZ

Application

Burner system with a pilot burner which is switched off once the main burner has ignited for processes which require high temperature accuracy and low circulation in the furnace, e.g. crucible and ladle heating, incineration installations, hot-air and steam generators, aluminium smelting furnaces…

Function

The capacity can be adjusted continuously by activating the air control valve (070) (analogue or 3-point step signal). The pneumatic ratio control system (020/030) controls the gas pressure proportionally to the air pressure and thus maintains a constant air/gas ratio. At the same time, it acts as an air deficiency cut-out. Adjusting valves and/or butterfly valves are used for limiting the air and gas flow rates and for adjusting the air/gas ratio.

Furnace pressure fluctuations have the same effect on the gas and air flow so that the air/gas ratio will remain unchanged.

The pilot burner has its own gas and air supply and is directly electrically ignited and controlled. The pilot flame ignites the main burner and can be switched off once the burner has ignited successfully.

Ignition and monitoring are ensured by an automatic burner control unit (090), which must be approved for continuous operation if the burner is to operate for more than 24 hours, in accordance with EN 746-2.

Note

For burner capacities between 120 and 360 kW, ignition with reduced capacity is required pursuant to EN 746-2:2010 (slow opening gas valves).

The pneumatic ratio control system in conjunction with a defined ignition position of the air control valve is an equivalent alternative to the pilot gas bypass according to figure D.14 in Annex D of EN 746-2:2010. The ignition position of the air control valve is to be monitored using limit switches or pressure switches in the air circuit.

Ignition with up to 50% of the burner capacity with a safety time of 3 seconds complies with the requirements of the Standard.

For burner capacities greater than 1200 kW, the valves must be equipped with an automatic valve proving system (TC).

DOCUTHEK

You can find all documents here.

 

docuthek.com